TAOTRONICS TT-BA09 Pro Wireless Audio Adapter User Guide

Contents hide

1 TAOTRONICS TT-BA09 Pro Wireless Audio Adapter

5 Documents / Resources

5.1 References

6 Related Posts

TAOTRONICS TT-BA09 Pro Wireless Audio Adapter

PACKAGE CONTENTS

1 x TaoTronics Wireless Adapter (TT-BA09 Pro)
1 x 3.5mm Audio Cable

1 x 3.5mm Female to RCA Male Cable
1 x Optical Cable

1 x USB-C Charging Cable
1 x User Guide

PRODUCT DIAGRAM

A for 1st Device
B for 2nd Device

Codec Indicators
Transmitter (TX) / Receiver (RX) Mode Switch

Power ON/OFF/Pairing
Power Indicator

BUTTON CONTROL

LED INDICATOR STATUS

Indicators	Function	Status
Power Indicator	Power ON	Flashing twice
	Power OFF	Flashing twice
	Standby Mode	Flashing every 5 seconds
	Battery Low	Solid on
	Charging	Solid on
	Fully Charged	Off
A	Pairing	Flashing quickly
	Connected	Solid on
	Re-connect	Flashing slowly
B	Pairing	Flashing quickly
B	Connected	Solid on
SBC	Connected using the SBC codec	Solid on
APTX	Connected using the Apt-X® codec	Solid on
LL	Connected using the Apt-X Low Latency® codec	Solid on

SBC: SBC codec, supported by most Bluetooth® devices
APTX: Apt-X® codec, the Bluetooth® device shall support Apt-X® codec. Prior than SBC.

LL: Apt-X Low Latency® codec, the Bluetooth® device shall support Apt-X low latency®. Prior than SBC and Apt-X®.

HOW TO USE

Charging

Connect the charging port with any USB charging adapter or active computer USB port.
the Power indicator will stay solid on during charging. Once fully charged, it will turn off.

Note:

You can use the adapter during charging, however, there might be background buzz noise.

We recommend charging the unit for at least 2 hours before using it for the ﬁrst time.

Use in TX Mode | Initial Pairings
Pair with the 1st Bluetooth® Device
Successfully paired: “A” solid on, the Codec indicator for the current streaming codec will light up

Note:

If you want to experience LIP SYNC, make sure your Bluetooth® device supports apt-X Low Latency® codec. After connected, the Codec indicator “LL” will light up to indicate the low latency streaming codec.

The default input mode is SPDIF. When the AUX cable is plugged in, it will switch to AUX mode automatically.
Please do not connect TT-BA09 Pro to an ampliﬁer output in TX mode, which may cause over-voltage and damage the adapter.

Pair with the 2nd Bluetooth® Device

Note:

After connecting with two Bluetooth® devices, the Codec indicator for the highest codec supported by both devices will light up (e.g., if device “A” supports SBC and Apt-X codec, while device “B” supports SBC codec, then Codec indicator “SBC” will light up).
After disconnecting with one of the devices, the Codec indicator for the highest codec supported by the remaining device will stay on.

Use in TX Mode | Automatic Re-connect
TT-BA09 Pro can remember the devices paired previously, and will attempt to pair with the last connected devices (up to 2 devices) automatically once it is turned on.

Use in TX Mode | Clear Pairing History
When the adapter is off, clear the pairing history by sliding the Mode switch to “RX”, then power it on.

Use in TX Mode | Use with your TV Check your TV output options before the set up
TVs with OPTICAL audio out

Ensure your TV speaker is set to “External Speaker”.
Ensure TV audio format is set to “PCM” or “Dolby/DTS” is OFF (This is IMPORTANT).
Ensure the optical audio cable is plugged in “SPDIF IN” port on TT-BA09 Pro.
Note: Setting menu may be different depending on different TV brands and models.

TVs with AUX 3.5mm audio out

TVs with RCA audio out (Red/White ports labeled “AUDIO OUT”)

Use in TX Mode | Use with your PC/LaptopUse in RX Mode | Initial Pairing Pair with the 1st Bluetooth® Device

Slide the Mode switch to “RX” mode.
Press and hold the Power button for 3 seconds to turn on the adapter.
For the ﬁrst use, TT-BA09 Pro will enter pairing mode automatically with indicator “A” ﬂashing quickly.
Activate the Bluetooth® function on your phone/tablet, ﬁnd “TaoTronics TT-BA09 Pro” in the search results and tap to connect. Once connected, the indicator “A” will turn solid on.

Pair with the 2nd Bluetooth® Device

After connecting with the 1st Bluetooth® device, press the Power button twice, the indicator “B” will ﬂash quickly.
Place your 2nd Bluetooth® device close to the adapter (within 3 feet / 1 meter). Activate the Bluetooth® function on your phone/tablet, ﬁnd “TaoTronics TT-BA09 Pro” in the search results and tap to connect. Once connected, the indicator “B” will turn solid on.

Use in RX Mode | Automatic Re-connect
TT-BA09 Pro can remember the devices paired previously, and will attempt to pair with the last connected devices (up to 2 devices) automatically once it is turned on.

Use in RX Mode | Clear Pairing History
When the adapter is off, clear the pairing history by sliding the Mode switch to “TX”, then power it on.

TROUBLESHOOTING

Problem	Solutions
No audio input	Make sure that you have followed the instructions for cable connections and settings on TV/PC/Laptop.
Audio delay	Make sure your Bluetooth® device supports apt-X Low Latency® codec. After connected, the Codec indicator “LL” will light up to indicate the low latency streaming codec.
Pair with a new Bluetooth® device	When TT-BA09 Pro is powered on, press the Power button twice to enter pairing mode before reconnecting to the paired device.
Can’t reconnect with the last connected device	Each time you switch the modes, the pairing history will be cleared. Please re-pair with your Bluetooth® device as instructed.

WARRANTY AND SERVICE
Thank you for choosing the TaoTronics TT-BA09 Pro Wireless Adapter. If any problems occur, please contact the TaoTronics Customer Care Centre in your country via the contact information listed in this User Guide.